Camp's Organ Service
by Trek II Products*, Benton Electronics* and More
By Benton Electronics Converts older single speed Leslie's to two
speed using original motors. It replaces both the old mechanical relay and provides fast and slow
speed operation. Optionally adds brake function. Uses Standard Motor Drive Technology, thus avoiding
problems such as low torque, motor heat and growling noise with slow speed.
This unit adds the famous Hammond B3 style percussion sound to pre-B3 Hammond consoles. It mounts in place of the upper left hand check block. The TP-2B not only provides for the B3 style percussion, but gives you an additional percussive voice and more control.
•Three harmonics - 2nd, 3rd and 5th
•Level controls for each harmonic
•Adjustable decay rate
This kit provides a ¼” Bass Output and a ¼” Full Range Output with volume control to any spinet or console Hammond organ, making your organ ready for any combo amp or mixing board. It also provides a great way to boost your bass.
Aging resistors,tubes and capacitors can become noisy and unreliable. The SSP-3 is a solid state replacement for most standard Hammond tone wheel consoles. The SSP-3 has been carefully designed to faithfully reproduce the response of the original tube pre-amp when it was new.
•Built in reverb
•Built in power supply
•Built in Leslie 122 tremolo control circuitry
•Built in B3 style percussion
•Percussion control head - enables percussion voices for pre-B3 consoles"
•Auxiliary amplifier channels provides amplifier input for keyboards, rhythm units, etc.
B3s were made from 1955 to 1975 and the components within the preamp are old and aging. As components within the preamp age,they drift in value and sometimes breakdown causing intermittent statics, hums, poor bass or treble response, etc. Replace your aging tube preamp with a rebuilt tube preamp, all resistors, capacitors, potentiometers and tubes have been replaced, also an improved power supply for a cleaner sound has been added, and the chassis is treated to prevent the growth of zinc dendrites. The warmth of a tube preamp is retained and the original (now disconnected) capacitors are left in place for asthetics. It comes with installation and a one year warranty. Exchange required.
For use in most standard Hammond consoles. Uses a full size three spring delay line for a natural reverb sound. Designed specifically to interface with vacuum tube circuitry of Hammond tone wheel consoles.
•Includes reverb level control
•Designed for Hammond tone wheel consoles
•Full size three spring delay
Just like the originals, inside and out. These switches will give you the vintage look and feel your are looking for.
Trek II Echo / Tremolo Switches
Mounts in place of the lower left hand end block on standard Hammond tone wheel consoles.
Allows convenient rocker switch control of the tremolo function. Two electrically isolated switch
sections allow the control of dissimilar Leslies with a single switch. Pre-punched mounting hole
provided for addition of a reverb or other control in the same enclosure.
When ordered along with Trek II Reverb or SSP-3 Solid State Preamp, the Tremolo switches can be
supplied with the reverb control pre-installed in the end block cover.
Works with most Hammond organs utilizing a top octave generator IC (MDD). Will allow the organ pitch to be shifted in discrete semitone steps as much as two semitones sharp or four semitones flat.
•Shift your playing into a singer's vocal range
•Modulate from key to key
•Accompany other instruments playing in "difficult" keys
The TR-3 Transposer is not compatible with tone wheel type organs.
Allows most single channel Leslie speakers to be driven by your portable organ, guitar, synthesizer or mixer. It provides two 1/4" phone jack inputs, one for high level signals, one for low level signals.
•Foot switch tremolo control
•Foot switch power on/off
•Power and tremolo indicators
•Input level and tone controls
•Four different outlets to accommadate each of the following Leslie families listed below.
*NOTES: The UC-1A will also function with 700, 705, 710, 720 and 730 type cabinets when the LCO-1 or LCO-1A crossover is installed in tone cabinet. Model 31H is compatible only if above serial # 5200. Models 25, 45, 125, and 225 are compatible only if equipped with amplifier.
Provides 25 notes of deep rich bass with sustain and pluck effect. Installs in standard consoles utilizing the existing pedal switch contacts. Separate 8' and 16' outputs function with the existing pedal drawbars. Although designed to be played from the existing pedals, it will work with any single make contact assembly or keyboard.
•Adjustable sustain length
•Adjustable pluck effect
•Quartz tuning accuracy
•Separate outputs for connection to external amplifier
The SB-2500A is also available in a version for use as a replacement bass pedal generator in organs with unreliable, unrepairable, or poor sounding pedal sections (E100,R100,etc.)..
*Trek II is a registered trademark of Trek II Products, Inc.
Copyrighted images by Trek II Products, Inc., used with permission
*Benton Electronics is a registered trademark of Benton Electronics.
Copyrighted images by Benton Electronics, used with permission